{"id":439,"date":"2017-03-31T16:25:28","date_gmt":"2017-03-31T20:25:28","guid":{"rendered":"http:\/\/www.circuitcrush.com\/?p=439"},"modified":"2021-06-30T21:20:15","modified_gmt":"2021-07-01T01:20:15","slug":"types-of-electrical-grounding","status":"publish","type":"post","link":"https:\/\/www.circuitcrush.com\/types-of-electrical-grounding\/","title":{"rendered":"Getting Grounded: Types of Electrical Grounding and What They Mean"},"content":{"rendered":"<h1><strong>An Intro to Grounding: Types of Electrical Grounding and What They Mean<\/strong><\/h1>\n<p>Originally, the plan was to write about another topic.<\/p>\n<p>But after some thought and reflection, it occurred to me that there is very little information about electrical grounds and grounding.<!--more--><\/p>\n<p>If you\u2019re an electrician, you\u2019re hopefully familiar with grounding in homes and buildings (Earth grounding). But there are different types of grounds and not a lot of information is available to non-construction oriented electronics enthusiasts.<\/p>\n<p>Even many engineering texts seem to completely ignore the subject and fail to give any practical explanation or meaning to the term ground.<\/p>\n<p>To make matters worse, electronics enthusiasts often confuse and incorrectly interchange the symbols for the different types of electrical grounding.<\/p>\n<p>For example, you may think that your car has a \u201cground\u201d. The truth is your car sits on four insulators and is not at all electrically connected to the Earth.<\/p>\n<p>So what does all this mean? Let\u2019s take a closer look at the types of electrical grounding and what the term \u201cground\u201d really means.<\/p>\n<h2><strong>Electrical Grounding 101<\/strong><\/h2>\n<p>Technically, the term \u201cground\u201d refers to a physical connection to the Earth. This symbol is shown in part (a) of the figure below. All too often, this symbol appears on circuits that do not connect to the Earth at all.<\/p>\n<p>&nbsp;<\/p>\n<p><img fetchpriority=\"high\" decoding=\"async\" class=\"aligncenter wp-image-440\" src=\"http:\/\/www.circuitcrush.com\/wp-content\/uploads\/Electrical-Grounding-Types.jpg\" alt=\"Electrical Grounding Types\" width=\"560\" height=\"280\" srcset=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Electrical-Grounding-Types.jpg 720w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Electrical-Grounding-Types-600x300.jpg 600w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Electrical-Grounding-Types-150x75.jpg 150w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Electrical-Grounding-Types-300x150.jpg 300w\" sizes=\"(max-width: 560px) 100vw, 560px\" \/><\/p>\n<p>&nbsp;<\/p>\n<p>This is the one that many electricians are familiar with. In your home, one (or maybe more) 8 foot copper coated rods are driven into the Earth. You\u2019ll often find this near the meter outside. A copper wire connects the ground rod to the main electrical distribution box (or panel).<\/p>\n<p>This symbol belongs on your home wiring plan. It can also go on a schematic diagram to indicate the Earth ground of an antenna system. You may also notice that your telephone and\/or cable company also uses this rod as a ground for their systems.<\/p>\n<p>Why does this work?<\/p>\n<p>The Earth is an extremely large conducting mass in which there is virtually zero resistance between any two points. Think of it as a giant reservoir of charge. Since it is electrically neutral, an equal number of positive and negative charges are distributed throughout its entire mass. Because of this, the Earth is at zero potential.<\/p>\n<p>The National Electrical Code mandates that the resistance between this rod and Earth be 25 ohms or less.<\/p>\n<p>Another popular electrical grounding spot in buildings is the cold-water pipe, since the pipe that supplies water to your home is likely buried in the ground and conductive.<\/p>\n<p>Not planning on connecting your latest microcontroller project directly to the Earth?<\/p>\n<p>No problem.<\/p>\n<p>I\u2019ve already alluded to the fact that there is more than one type of ground. As an electronics enthusiast, you\u2019re likely to see three different types of grounds that all have different meanings and schematic symbols.<\/p>\n<h2><strong>Electrical Grounding: Chassis Ground<\/strong><\/h2>\n<p>In the figure above, part (b) depicts the chassis ground. This is the correct symbol to use when referring to your vehicle. It can also indicate things such as the frame of a plane, or the metal box that you\u2019re going to enclose your project in.<\/p>\n<p>In your car, the negative terminal of your battery connects to the frame and\/or engine block. Thus, the entire metal body of the car which is at the same potential (hopefully) of zero volts is the electrical reference point (a.k.a. ground, or more correctly, chassis ground).<\/p>\n<p>In your widget that lives in a metal box, this is usually done with a ring terminal and a screw.<\/p>\n<p>Note that if your creation runs on batteries you may not even need to use a chassis ground.<\/p>\n<p>We\u2019ve all put our projects in plastic boxes before, which brings us to the next and most common type of \u201cground.\u201d<\/p>\n<h2><strong>Electrical Grounding: Circuit Common<\/strong><\/h2>\n<p>Part (c) of the figure above depicts the symbol for the circuit common. This is really just a common reference point in a given circuit. This is the symbol that you should use most often rather than the other two for most of your projects. On printed circuit boards, this is often the large-area copper foil layer (a.k.a. ground plane) of the board.<\/p>\n<p>Sometimes, you\u2019ll see a letter inside the triangle part to notate different types of returns (like the signal common).<\/p>\n<p>This is because a condition known as a ground loop (technically, a common loop) can arise when commons are shared between, say, power and signal.<\/p>\n<p>So why is this type of \u201cground\u201d technically referred to as common?<\/p>\n<h3 style=\"text-align: center;\">Become the Maker you were born to be. Try <a href=\"https:\/\/learnarduinonow.com\">Arduino Academy<\/a> for FREE!<\/h3>\n<p><img decoding=\"async\" class=\"aligncenter  wp-image-4238\" src=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2.png\" alt=\"\" width=\"423\" height=\"161\" srcset=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2.png 828w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-300x114.png 300w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-150x57.png 150w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-768x292.png 768w\" sizes=\"(max-width: 423px) 100vw, 423px\" \/><\/p>\n<p>When we measure voltage, we always measure it with respect to some other point. For example, when we measure the voltage drop across a resistor, we are measuring the voltage on one node with respect to the other node, with the resistor sitting between the two nodes. This is an example of measuring a voltage drop \u201cacross\u201d a resistor.<\/p>\n<p>To say we\u2019re measuring voltage a specific point doesn\u2019t make sense as voltage is a potential difference and having a difference of any kind implies there are two things to compare. Rather, if someone asks you to measure the voltage at point A in circuit, they mean at point A with respect to the circuit common.<\/p>\n<p>For all the uber-nerds, the formal scientific definition of voltage is the equation below.<\/p>\n<p>V<sub>ba<\/sub> = &#8211; \u222b <strong>E <\/strong><strong>\u2219 <\/strong>d<strong>l <\/strong><\/p>\n<p>Where the integral is from point a to point b, <strong>E<\/strong> is the electric field, and d<strong>l<\/strong> is an infinitesimal increment of displacement.<\/p>\n<p>This equation uses calculus and is one you may be familiar with if you\u2019ve studied engineering. The typical enthusiast should not have to worry about this, though you should feel free to investigate further if that sort of thing interests you.<\/p>\n<p>Often, you\u2019ll find yourself measuring voltage with respect to \u201cground\u201d or the common point of the circuit. This is because this point should be at zero potential or 0 V. An exception would be measuring the voltage across one resistor in a network of resistors.<\/p>\n<p>Confused? Check out the diagram below.<\/p>\n<p>&nbsp;<\/p>\n<p><img decoding=\"async\" class=\"aligncenter size-full wp-image-441\" src=\"http:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground.jpg\" alt=\"Circuit Common Electrical ground\" width=\"1041\" height=\"474\" srcset=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground.jpg 1041w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-600x273.jpg 600w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-150x68.jpg 150w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-300x137.jpg 300w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-768x350.jpg 768w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-1024x466.jpg 1024w\" sizes=\"(max-width: 1041px) 100vw, 1041px\" \/><\/p>\n<p>&nbsp;<\/p>\n<p>In this picture, point C would normally be the circuit common. Notice how point C connects to the negative terminal of the 18 V battery. When measuring voltage, you normally place the negative probe of the voltmeter on the circuit common.<\/p>\n<p>Resistors R<sub>1<\/sub> and R<sub>2<\/sub> are a \u201cnetwork\u201d so if I want just the voltage across R<sub>1<\/sub>, point B would become my reference rather than point C.<\/p>\n<p>Why?<\/p>\n<p>Because point B is lower in potential than point A. Put another way, point B is more negative than point A. Of course, resistors don\u2019t actually have a polarity. The + and \u2013 symbols are there to represent the voltage drop and the fact that there is a potential difference between points A and B.<\/p>\n<p>If we were to put the negative probe on point B and the positive on point C to measure the voltage across R<sub>2<\/sub>, we\u2019d get the -12 V shown by the dotted arrow. If we were to measure the voltage across R<sub>2<\/sub> the conventional way (with point C as the reference), we\u2019d get +12 V as the solid arrow shows.<\/p>\n<p>Notice that the absolute value of the voltages is the same regardless of how we orient our meter probes.<\/p>\n<p>Of course, if we were to measure the voltage across both resistors, we\u2019d get the full 18 V (or -18 V if the probes were reversed).<\/p>\n<h2><strong>Uncommon Commons<\/strong><\/h2>\n<p>So far, the circuit common has been associated with the most negative part of the circuit, usually the negative terminal of the battery or power supply.<\/p>\n<p>The truth is the circuit common can be anywhere. The picture below from the 4<sup>th<\/sup> edition of Practical Electronics for Inventors illustrates this concept (though the ground symbol is technically incorrect).<\/p>\n<p>&nbsp;<\/p>\n<p><img loading=\"lazy\" decoding=\"async\" class=\"aligncenter size-full wp-image-442\" src=\"http:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-2.jpg\" alt=\"Circuit Common \/ Ground 2\" width=\"720\" height=\"358\" srcset=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-2.jpg 720w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-2-600x298.jpg 600w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-2-150x75.jpg 150w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/Circuit-Common-Electrical-Ground-2-300x149.jpg 300w\" sizes=\"(max-width: 720px) 100vw, 720px\" \/><\/p>\n<p>&nbsp;<\/p>\n<p>Take a look at the three terminals in each picture. The first part of the picture has the circuit common tied to the negative terminal of the lower battery, as expected. Each individual battery is supplying 1.5 V with both in series supplying 3 V.<\/p>\n<p>However, the common in the second picture is now in between the two batteries. Notice how each battery is still 1.5 V, but rather than obtaining 1.5 V and 3 V as in the first picture, we obtain +1.5 V and -1.5 V. The battery connection is the same, so why is this possible?<\/p>\n<p>Simply because the common, or reference point, is in a different area. Remember, when you measure voltage, you\u2019re measuring the potential difference between two points. Often, one of the two points will be the circuit common. If the common point moves, the voltage may be different even if the circuit is the same!<\/p>\n<p>Most often, you\u2019ll be working with circuits similar to the first picture.<\/p>\n<p>But split power supplies (like the second picture) are somewhat common in audio and other types of circuits where sinusoidal signals swing between negative and positive voltages (relative to 0 V, of course).<\/p>\n<p>One last thing to notice is that the total potential difference in both circuits is 3 V, regardless of where the reference is. After all, two 1.5 V batteries alone are only capable of producing a maximum difference of 3 V.<\/p>\n<h2><strong>Grounding for Safety<\/strong><\/h2>\n<p>Before we wrap up, we need to take a quick second look at Earth grounds.<\/p>\n<p>Besides acting as a reference point, Earth ground is there to protect you from electrical shock.<\/p>\n<p>How?<\/p>\n<p>As an example, let\u2019s say that a hot wire inside your dryer somehow comes into contact with the inside of the dryer\u2019s metal body. Without an Earth ground, touching the dryer may cause shock or even death.<\/p>\n<p>However, since the case of the dryer connects to Earth ground, the current shunts away saving your life and likely tripping the breaker due to the short. In fact, a hot to ground short will usually trip the breaker the instant it occurs.<\/p>\n<p>Grounding also helps with electrostatic discharge. So, when you take a walk across the carpet, the charge on your body (which can be tens of thousands of volts) goes to ground rather than frying the ICs in your gadget.<\/p>\n<h2><strong>Are You Grounded Yet?<\/strong><\/h2>\n<p>Grounding can be a complex and mysterious subject to many. All too often books, educational courses, and tutorials either quickly gloss over it (if they cover it at all) or do a poor job of explaining it.<\/p>\n<p>Hopefully, this post removed some of the mystery surrounding electrical grounding (rhyme intended).<\/p>\n<p>As with most things in electronics, there is a lot more to say about grounding. Perhaps a future post will revisit the topic.<\/p>\n<p>Meanwhile comment and tell me what your biggest questions on grounding are. That way, I have some ideas on what to write about!<\/p>\n<h2 style=\"text-align: center;\">Become the Maker you were born to be. Try <a href=\"https:\/\/learnarduinonow.com\">Arduino Academy<\/a> for FREE!<\/h2>\n<p><img loading=\"lazy\" decoding=\"async\" class=\"aligncenter size-full wp-image-4238\" src=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2.png\" alt=\"\" width=\"828\" height=\"315\" srcset=\"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2.png 828w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-300x114.png 300w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-150x57.png 150w, https:\/\/www.circuitcrush.com\/wp-content\/uploads\/FB_Cover2-768x292.png 768w\" sizes=\"(max-width: 828px) 100vw, 828px\" \/><\/p>\n<a target=\"_blank\" href=\"https:\/\/www.drpeterscode.com\/index.php\"><img src=\"https:\/\/www.circuitcrush.com\/wp-content\/plugins\/dpabottomofpostpage\/apixel1x1.jpg\" ><\/a><table><\/table>","protected":false},"excerpt":{"rendered":"<p>An Intro to Grounding: Types of Electrical Grounding and What They Mean Originally, the plan was to write about another topic. But after some thought and reflection, it occurred to me that there is very little information about electrical grounds and grounding.<\/p>\n","protected":false},"author":1,"featured_media":446,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_genesis_hide_title":false,"_genesis_hide_breadcrumbs":false,"_genesis_hide_singular_image":false,"_genesis_hide_footer_widgets":false,"_genesis_custom_body_class":"","_genesis_custom_post_class":"","_genesis_layout":"","_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[69],"tags":[74,73,70,71,72],"class_list":{"0":"post-439","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-grounds-and-grounding","8":"tag-chassis-ground","9":"tag-circuit-common","10":"tag-ground","11":"tag-grounding","12":"tag-types-of-grounds","13":"entry"},"jetpack_sharing_enabled":true,"jetpack_featured_media_url":"https:\/\/www.circuitcrush.com\/wp-content\/uploads\/electrical-grounding.jpeg","_links":{"self":[{"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/posts\/439","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/comments?post=439"}],"version-history":[{"count":1,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/posts\/439\/revisions"}],"predecessor-version":[{"id":4344,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/posts\/439\/revisions\/4344"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/media\/446"}],"wp:attachment":[{"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/media?parent=439"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/categories?post=439"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.circuitcrush.com\/wp-json\/wp\/v2\/tags?post=439"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}